Neuromuscular impairments resulting from conditions such as spinal cord injuries, strokes, and multiple sclerosis can greatly affect the quality of life of those affected, preventing them from carrying out typical activities of daily living. A number of active assistive devices have been proposed to provide upper limb assistance for such neuromuscular conditions. These devices primarily […]

Permanent magnets and magnetic field sensors are widely used in the automotive industry for the detection of the rotational speed of a gear or the torque measurement of gearbox shafts, vehicle axles, and electric motors. For instance, the action of a driving wheel can modify a magnetic pattern encoded in a transmission shaft. Magnetic sensors […]

The intern has developed a 3D microscopic model to simulate water bead behavior on hydrophobic and superhydrophobic coatings. The microscopic model developed at Concordia University which simulates one bead cannot be directly integrated into an aircraft icing panel code such as CANICE-2D. CANICE-2D approved by Transport Canada has been widely used at Bombardier Aerospace to […]

The project will determine sliding wear behaviour of lightweight Al and Mg alloys for the continuously variable transmission (CVT) bore application and other engine applications. High temperature lubricated wear tests that simulate the actual operating conditions of CVT bore will be carried out. In addition, tests will be conducted at room temperature and under the […]

Buildings have a high share of energy consumption in Canada. Real-time monitoring and analysis of energy use data can assist in improving the performance of the building and help reduce operating costs, lower utility bills, increase equipment life, improve occupants’ comfort, and increase retention and leasing rates; all while lowering carbon emissions. Joule M&V AI […]

Cancer is the leading cause of death in Canada. A promising new way to treat cancer is through the administration of immune cells that target the cancer – an approach called cancer immunotherapy. The goal of this project is to engineer better culture vessels to produce dendritic cells. Dendritic cells are the “gatekeepers” of our […]

Currently FCL obtains its power from SaskPower, which is the main utility company in Saskatchewan. SaskPower produces the bulk of electricity through burning fossil fuel. To change this SaskPower is encouraging the public to install renewable energy systems and connect to their electrical grid. FCL will take advantage of SaskPower’s programs and install renewable energy […]

La prévalence des lésions au système musculo-squelettique est très élevée (29,8 % parmi toutes les catégories de maladies chroniques). Parmi ces lésions, un grand pourcentage concerne l’articulation du genou. Plusieurs études ont montré que les données biomécaniques permettent une évaluation fonctionnelle de l’état du genou. Le système d’acquisition de données KneeKG permet une analyse précise, […]

La fatigue etant la principale causes de defaillance des turbines hydroelectriques, il devient essentiel d’estimer la performance des methodes d’inspection non destructives presentement utilisees par les producteurs d’energie (inspection visuelle etlou ultrasonore) pour detecter et caracteriser les manifestations de ceUe fatigue. Le developpement de modeles probabilistes, qui lient I’historique des conditions operatoires des turbines, I’evolution […]

The integrity of energy pipelines is managed using information obtained from in-line inspections, which are periodically performed non-destructive inspections of the pipe wall to detect and size defects like corrosion, cracks, and dents. The coordinate systems for referencing the locations of the detected defects varies from inspection to inspection. It is therefore necessary to align […]

L’utilisation des outils d’analyse du cycle de vie permet de réduire considérablement l’impact environnemental des bâtiments. À l’aide de ces résultats, les concepteurs peuvent améliorer la performance environnementale de leurs bâtiments. Toutefois, l’utilisation de ces outils dans le domaine est encore très peu répandue. Afin de faciliter leur adoption, plusieurs fournisseurs de logiciels proposent des […]

There is an increasing trend towards miniaturization in the microelectronics industry which increases the power density and thus heat generated from these devices. Consequently, one key factor limiting reliability and higher performance of electronic devices is the heat removal, to maintain the device below its maximum operating temperature. This indicates the importance of devising efficient […]