Power systems are becoming more open, stochastic and dynamic nonlinear as the integration of renewable energy sources are keeping increasing. On the other hand, power systems are usually confronted with various weather conditions and fortuitous events that may lead to incidents causing instability of the networks. This research will propose an on-line transient stability prediction […]

The aim of this research and development project is to design and develop a bedside point-of-care device to be equipped with the CardiAI’s machine learning technology for heart failure management. our POC system will include disposable cardiac biomarker strips and an electronic reader. Once implemented, it will be connected to the AI platform that will […]

Ce projet s’attaque au délai de livraison d’un réseau de fabricants des meubles en bois avec la simulation informatique. L’objectif est de répondre aux deux questions suivantes; ‘et si l’entreprise enlève ou ajoute un tel produit de sa ligne de montage, diminuera-t-elle son temps de passage?’ et ‘et si les fournisseurs changent leurs aménagements, diminueront-t-ils […]

Many mineral ores are concentrated by froth flotation, a process that often uses toxic chemicals to selectively alter mineral surface properties. With increasing regulatory restrictions, the industry could face a dead end with no alternative reagents that are sufficiently efficient, low cost or environment friendly. It has been previously shown that peptides could selectively bind […]

Northern Canada presents favorable conditions for bifacial solar installations due to typically higher albedo, caused by a high degree of snow cover, and low temperature, which is ideal for PV module efficiency. In addition, many northern and remote Canadian communities, including Iqaluit and Cambridge Bay, rely on diesel power. Bifacial solar presents a clean and […]

Four-bar linkages, consisting of four rigid links coupled by revolute joints forming a closed chain, can be found in a variety of applications, such as windshield wipers, pumps, window cranks, suspension systems, robots, and extraterrestrial rovers just to name a few. Designers of such mechanical systems are commonly confronted with the task of determining the […]

Hydraulic stimulation is a technique that is being used to increase the productivity and efficiency of natural resources under the ground. Hydraulic fracturing is a hydraulic stimulation method, in which the water is being injected into a borehole and that creates additional fractures within the hard rock formations. This may extend the flow network within […]

The phenomenon of near-limit detonation propagation, where detonations have been experimentally observed to propagate at average speeds smaller than the ideal Chapman-Jouguet (CJ) detonation speeds, has attracted extensive efforts on determining the influencing mechanisms through application of simple models for predicting such velocity deficits. Despite the large number of attempts to experimentally investigate the dynamics […]

The City of Surrey has about 500 vehicles in its municipal fleet, ranging from light-duty passenger vehicles to heavy-duty commercial vehicles or trucks. Because of increasing political and public pressure to reduce carbon footprint from municipal fleets, the City is interested in finding viable low-carbon alternative fuel vehicles to their conventional gasoline and diesel vehicles. […]

The goal of this research project is to establish a working robotic “hand”, or gripper, that will be able to perform surgical instrument handoff to operating room staff members during surgery. This project will involve a both McGill University and Kinova, the partner organization. Kinova will benefit from this project through increased collaboration with academia, […]

With this collaborative project we plan to proof that non-stick, self-emptying containers can be produced through molding the polymer with a laser-micromachined steel mold. Imparting a Nature-inspired functional microstructure through laser-machining onto metals is a well understood method developed in Prof. Kietzig’s lab. By using a laser-structured metal mold to form plastics, we will imprint […]

Le projet envisagé, a pour cadre l’industrie manufacturière, plus précisément, les activités liées à l’assemblage des composants d’aéronefs et de véhicules de transport. De façon régulière dans ces secteurs, l’assemblage est effectué grâce à des gabarits dédiés à effectuer une seule tâche. Lorsque celle-ci doit être changée ou modifiée, le gabarit doit subir des modifications […]